bannera

Book A.
Introduction

Book B.
7150 Requirements Guidance

Book C.
Topics

Tools,
References, & Terms

SPAN
(NASA Only)

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Migration of unmigrated content due to installation of a new plugin


Alias
aliasSWE-137

Tabsetup
1. The Requirement
1. The Requirement
12. Rationale
23. Guidance
34. Small Projects
45. Resources
56. Lessons Learned


Div
idtabs-1

1. Requirements

4.3.2 The project shall perform and report on software peer reviews/inspections for:

      a. Software Development or Management Plan.
      b. Software Configuration Management Plan.
      c. Software Maintenance Plan.
      d. Software Assurance Plan.
      e. Software Safety Plan.

1.1 Notes

NPR 7150.2,  NASA Software Engineering Requirements, does not include any notes for this requirement.

1.2 Applicability Across Classes

Classes C through E and Safety Critical are labeled with "P (Center) + SO." "P (Center)" means that an approved Center-defined process which meets a non-empty subset of the full requirement can be used to achieve this requirement while "SO" means that the requirement applies only for safety critical portions of the software.

Class C and Not Safety Critical as well as Class G are labeled with "P (Center)." This means that an approved Center-defined process which meets a non-empty subset of the full requirement can be used to achieve this requirement.

Class F is labeled with "X (not OTS)." This means that this requirement does not apply to off-the-shelf software for these classes.


applicable
f*
gp
h0
ansc1
asc1
bnsc1
csc*
bsc1
esc*
cnscp
dnsc0
dsc*
ensc0



Div
idtabs-2

2. Rationale

Peer review/inspections are among the most effective V&V (Verification and Validation) practices for software

sweref
319
319
. They can be applied to many kinds of technical artifacts, and serve to bring together human judgment and analysis from diverse stakeholders in a constructive way.

Since well-developed and appropriate plans that have buy-in from key stakeholders are important elements of critical software success, peer review/inspections are applied to improve the quality of such plans.


Div
idtabs-3

3. Guidance

NASA-STD 2202-93, NASA Software Formal Inspection Standard, is currently being updated and revised to include lessons that have been learned by practitioners over the last decade. Included in this Standard are several best practices for performing inspections on the different software plans, including the recommended minimum content of checklists, which perspectives to be included in the inspection team, and the inspection rate.

The presence and participation of project management in peer review/inspection meetings are usually not recommended due to the potential negative impact to the effectiveness of the inspections. However, since the project management for both the software and the system are often the stakeholders of the work products examined (in the context of this requirement), they may be included as participants of the inspections only when necessary. In such situations, both the management and the other inspectors must be aware that defects found during inspections are never to be used for evaluating the authors.

NPR 7150.2 contains specific software documentation requirements for these plans. These content requirements are a basis of checklists as well as additional quality criteria relevant to inspections:


SWE-102

Software Development/Management Plan

SWE-103

Software CM Plan

SWE-105

Software Maintenance Plan

SWE-106

Software Assurance Plan

SWE-138

Software Safety Plan Contents


Additional guidance related to peer reviews and inspections may be found in the following related requirements in this Handbook:


SWE-088

Software Peer Reviews and Inspections - Checklist Criteria and Tracking

SWE-089

Software Peer Reviews and Inspections - Basic Measurements




Note

Consult Center Process Asset Libraries (PALs) for Center-specific guidance and resources, such as templates, related to peer reviews and inspections.



Div
idtabs-4

4. Small Projects

No additional guidance is available for small projects. The community of practice is encouraged to submit guidance candidates for this paragraph.


Div
idtabs-5

5. Resources


refstable

toolstable


Div
idtabs-6

6. Lessons Learned

The effectiveness of inspections for defect detection and removal in any artifact has been amply demonstrated. Data from numerous organizations have shown that a reasonable rule of thumb is that a well-performed inspection typically removes between 60 percent and 90 percent of the existing defects, regardless of the artifact type

sweref
319
319
.


...